Hotpoint Refrigerator HM 3x AA User Manual

HM 3x AA  
HM 3x AA AI  
English  
Operating Instructions  
REFRIGERATOR/FREEZER COMBINATION  
Contents  
Operating Instructions, 1  
Assistance, 2  
Description of the appliance, 3  
Installation, 4  
Start-up and use, 5  
Maintenance and care, 6  
Precautions and tips, 7  
Troubleshooting, 8  
 
Description of the appliance  
Overall view  
The instructions contained in this manual are applicable to different  
model refrigerators. The diagrams may not directly represent the  
appliance purchased. For more complex features, consult the  
following pages.  
1 STORAGE compartment *  
2 FREEZER and STORAGE compartment  
3 FRUIT and VEGETABLE bin *  
4 FOOD CARE ZONE for MEAT and CHEESE *  
5 WINE RACK *  
6 SHELVES *  
7 LAMP (see Maintenance) *  
8 Removable multipurpose SHELVES *  
9 BOTTLE shelf  
10 FRESH BOX *  
11 ACTIVE OXYGEN *  
12 AIR *  
13 TEMPERATURE REGULATING Knob  
14 SUPER FREEZE *  
* Varies by number and/or position, available only on certain  
models.  
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR 5 YEAR PARTS GUARANTEE ON 08448 24 24 24  
3
 
Changing the plug:  
Installation  
! Before placing your new appliance into operation please read  
these operating instructions carefully. They contain important  
information for safe use, for installation and for care of the  
appliance.  
GB  
Removing the plug  
If your appliance has a non-rewireable moulded plug and you  
should wish to remove it to add a longer cable or to re-route the  
mains cable through partitions, units etc. please ensure that either:  
-
The plug is replaced by a fused 13amp re-wireable plug  
bearing the BSI mark of approval.  
! Please keep these operating instructions for future reference.  
Pass them on to possible new owners of the appliance.  
or  
-
The mains cable is wired directly into a 13amp cable outlet,  
controlled by a switch (in compliance with BS 5733) which is  
accessible without moving the appliance.  
Positioning and connection  
Positioning  
1.Place the appliance in a well-ventilated humidity-free room.  
2.Do not obstruct the rear fan grills. The compressor and  
condenser give off heat and require good ventilation to operate  
correctly and save energy.  
Disposing of the plug  
Cut off and dispose of the supplied plug if it does not fit your socket.  
The cable should be cut as close as possible to the moulded plug.  
3.Ensure the appliance is away from any sources of heat (direct  
sunlight, electric stove, etc.).  
Remove the fuse.  
WARNING:  
Electrical connections  
To avoid a shock hazard do not insert the discarded plug  
into a socket anywhere else.  
After the appliance has been transported, carefully place it  
vertically and wait at least 3 hours before connecting it to the  
electricity mains. Before inserting the plug into the electrical socket  
ensure the following:  
Fitting a new plug  
IMPORTANT:  
• The appliance is earthed and the plug is compliant with the law.  
• The socket can withstand the maximum power of the appliance,  
which is indicated on the data plate located on the bottom left  
side of the fridge (e.g. 150 W).  
WIRES IN THE MAINS LEAD ARE COLOURED IN ACCORDANCE  
WITH THE FOLLOWING CODE...  
• The voltage must be in the range between the values indicated  
on the data plate located on the bottom left side (e.g. 220-  
240V).  
• The socket is compatible with the plug of the appliance. If  
the socket is incompatible with the plug, ask an authorised  
technician to replace it (see Assistance). Do not use extension  
cords or multiple sockets.  
! Once the appliance has been installed, the power supply cable  
and the electrical socket must be easily accessible.  
! The cable must not be bent or compressed.  
! The cable must be checked regularly and replaced by authorised  
technicians only (see Assistance).  
! The manufacturer declines any liability should these safety  
Green and Yellow - Earth  
Blue  
- Neutral  
- Live  
Brown  
measures not be observed.  
As the colours of the wires in the mains lead may not correspond  
with the coloured markings identifying the terminals in your plug,  
proceed as follows:  
WARNING:  
THIS APPLIANCE MUST BE EARTHED.  
-
-
-
Connect Green and Yellow wire to terminal marked ‘E’ or  
or coloured Green and Yellow.  
Connect Brown wire to terminal marked ‘L’ or coloured red or  
brown.  
Connect Blue wire to terminal marked ‘N’ or coloured Black  
or Blue.  
Replacing fuse covers:  
When replacing a faulty fuse, a 13amp ASTA approved fuse to BS  
1362 should always be used and the fuse cover re-fitted.  
If the fuse cover is lost, the plug must not be used until a  
replacement is obtained.  
Replacement fuse covers:  
If a 13amp plug (BS 1363) is used it must be fitted with a 13amp fuse.  
If a replacement fuse cover is fitted, it must be of the correct  
colour as indicated by the coloured marking or the colour that is  
embossed in words on the base of the plug.  
If you are in any doubt about the electrical supply to your  
machine, consult a qualified electrician before use.  
CE Marking certifies that this appliance conforms to the  
following EEC directives:  
Low Voltage Equipment - 73/23/EEC & 93/68 EEC  
Electromagnetic Compatibility 89/336/EEC, 92/31/EEC &  
93/68/EEC  
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR 5 YEAR PARTS GUARANTEE ON 08448 24 24 24  
4
 
With the Active Oxigen switched on, the device will operate  
a repeted cycle until the key is pressed again. There will be  
an Ozone emission noticed by the switching on of the green  
led located on the Active Oxigen device located in the fridge  
compartment and a stand-by cicle (without zone emission)  
noticed by blue light.  
Start-up and use  
GB  
Starting the appliance  
! Before starting the appliance, follow the installation instructions  
(see Installation).  
! Before connecting the appliance, clean the compartments and  
accessories well with lukewarm water and bicarbonate.  
! The appliance comes with a motor protection control system  
which makes the compressor start approximately 8 minutes  
after being switched on. The compressor also starts each time  
the power supply is cut off whether voluntarily or involuntarily  
(blackout).  
Using the refrigerator to its full potential  
• Use the TEMPERATURE ADJUSTMENT knob to adjust the  
temperature (see Description).  
• Place only cold or lukewarm foods in the compartment, not hot  
foods (see Precautions and tips).  
• Remember that cooked foods do not last longer than raw foods.  
• Do not store liquids in open containers. They will increase  
humidity in the refrigerator and cause condensation to form.  
Freezer Compartment  
When the product is switched on the freezer compartment is  
set to its default value of -18°C. We recommend that the SUPER  
FREEZE function is set (the freezer status bar continues to display  
the set value) in order to accelerate the cooling process of the  
compartment; when the inside of the compartment has reached  
its optimal temperature the function will be deactivated and the  
food may be placed inside.  
SHELVES: with or without grill.  
Due to the special guides the shelves are removable and the  
height is adjustable (see diagram), allowing easy storage of large  
containers and food. Height can be adjusted without complete  
removal of the shelf.  
AIR *  
It is recognizable due to the presence of the mechanism on the  
top part of the refrigerator compartment (see diagram).  
B
FOOD CARE ZONE *  
A
Area dedicated to the storage of fresh food, such as meat and  
fish. Thanks to the low temperature inside the compartment, the  
Food Care Zone extends the period of time for which the food  
can be stored, keeping it fresh for up to a week.  
AIR maximises air circulation, improving the efficiency of the  
evaporator and helping to achieve the optimal temperature inside  
the refrigerator as quickly as possible each time it has been opened.  
The blown air (A) is cooled when it comes into contact with the  
cold wall, whereas the hotter air (B) is sucked up (see diagram).  
FRESH BOX *  
This is the new container, designed to keep various foods (such  
as cheese and cold meats) fresher for longer. If it is not needed, it  
can easily be removed from the refrigerator compartment. If there  
is a Bottle Shelf, more internal space can be created by placing  
the Fresh Box directly inside it.  
ACTIVE OXYGEN *  
This device releases ozone molecules inside the refrigerator; ozone  
is a natural substance which combats bacteria and microorganisms,  
reducing their proliferation while limiting unpleasant odours.  
TEMPERATURE Indicator light*: to identify the coldest area in  
the refrigerator.  
1. Check that OK appears clearly on the indicator light (see  
Automatically defines the amount of ozone required for prolonging  
the freshness of foodstuffs, eliminating odours and preventing  
bacteria build-up.  
diagram).  
There may be a slight distinctive odour inside the refrigerator.  
The very same smell can sometimes be detected during a storm,  
due to the ozone produced as the charge in the lightning bolts is  
released; this is completely normal. The amount produced by the  
device is very small and abates quickly as the antibacterial action  
takes place.  
2. If the word “OK” does not appear it means that the temperature  
is too high: adjust the REFRIGERATOR OPERATION knob to a  
higher position (colder) and wait approximately 10 hours until  
the temperature has been stabilised.  
Device is activated pressing the dedicated switch located in right  
side of the Oxigen device.  
3. Check the indicator light again: if necessary, readjust it following  
the initial process. If large quantities of food have been added  
or if the refrigerator door has been opened frequently, it is  
normal for the indicator not to show OK. Wait at least 10 hours  
before adjusting the REFRIGERATOR OPERATION knob to a  
higher setting.  
* Varies by number and/or position, available only on certain  
models.  
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR 5 YEAR PARTS GUARANTEE ON 08448 24 24 24  
5
 
• The back of the appliance may collect dust which can be  
removed by delicately using the hose of a vacuum cleaner set  
on medium power. The appliance must be switched off and  
the plug must be pulled out before cleaning the appliance.  
LED *  
GB  
Thanks to the powerful light it emits, the new LED lighting system  
offers a clear view of all foods, with no shadowy areas. If the LED  
needs to be replaced, please contact the Technical Assistance  
Service.  
Avoiding mould and unpleasant odours  
• The appliance is manufactured with hygienic materials which  
are odour free. In order to maintain an odour free refrigerator  
and to prevent the formation of stains, food must always be  
covered or sealed properly.  
• If you want to switch the appliance off for an extended period  
of time, clean the inside and leave the doors open.  
Defrosting the appliance  
! Follow the instructions below.  
Do not speed up the defrosting process by using any devices  
or tools other than the scraper provided, you may damage the  
refrigeration circuit.  
Using the freezer to its full potential  
• Do not re-freeze food that is defrosting or that has already been  
defrosted. These foods must be cooked and eaten (within 24  
hours).  
• Fresh food that needs to be frozen must not come into contact  
with food that has already been defrosted. Fresh food must  
be stored in the top FREEZER and STORAGE compartment  
where the temperature drops below -18°C and guarantees  
rapid freezing.  
Defrosting the refrigerator compartment  
The refrigerator has an automatic defrosting function: water is  
ducted to the back of the appliance by a special discharge outlet  
(see diagram) where the heat produced by the compressor causes  
it to evaporate. It is necessary to clean the discharge hole regularly  
so that the water can flow out easily.  
• Do not place glass bottles which contain liquids, and which  
are corked or hermetically sealed in the freezer because they  
could break.  
• The maximum quantity of food that may be frozen daily is  
indicated on the plate containing the technical properties  
located on the bottom left side of the refrigerator compartment  
(for example: Kg/24h: 4)  
! Do not open the door during freezing.  
! If there is a power cut or malfunction, do not open the freezer  
door. This will help maintain the temperature inside the freezer,  
ensuring that foods are conserved for at least 9 -14 hours.  
! In order to obtain a greater amount of space in the freezer  
compartment, you may remove the bins (except the lowest bin  
and the special COOL CARE ZONE bin, which has an adjustable  
temperature) and place the food directly onto the evaporator  
plates.  
Defrosting the freezer compartment  
If the frost layer is greater than 5 mm, it is necessary to defrost  
manually:  
1. Set the TEMPERATURE ADJUSTMENT knob to the position OFF  
2. Wrap frozen foods in newspaper and place them in another  
freezer or in a cool place.  
3. Leave the door open until the frost has melted completely. This  
can be made easier by placing containers with lukewarm water  
in the freezer compartment.  
SUPER FREEZE *  
The “Super Freeze” button enables intensive chilling so that the  
desired temperature is reached quickly. Once the fresh food is  
frozen, set the switch back to the OFF position. WARNING: in  
order to save energy, make sure the function is switched off after  
24 hours.  
4. Clean and dry the freezer compartment carefully before  
switching the appliance on again.  
Maintenance and care  
Replacing the light bulb *  
To replace the light bulb in the refrigerator compartment, pull out  
the plug from the electrical socket. Follow the instructions below.  
Access the light bulb by removing the cover as indicated in the  
diagram. Replace it with a similar light bulb within the power range  
indicated on the cover.  
Switching the appliance off  
During cleaning and maintenance it is necessary to disconnect  
the appliance from the electricity supply.  
It is not sufficient to set the temperature adjustment knobs on OFF  
(appliance off) to eliminate all electrical contact.  
Cleaning the appliance  
• The external and internal parts, as well as the rubber seals may  
be cleaned using a sponge that has been soaked in lukewarm  
water and bicarbonate of soda or neutral soap. Do not use  
solvents, abrasive products, bleach or ammonia.  
• The removable accessories may be soaked in warm water and  
soap or dishwashing liquid. Rinse and dry them carefully.  
*Varies by number and/or position, available only on certain models.  
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR 5 YEAR PARTS GUARANTEE ON 08448 24 24 24  
6
 
Respecting and conserving the  
Precautions and tips  
GB  
environment  
• Install the appliance in a fresh and well-ventilated room. Ensure  
that it is protected from direct sunlight and do not place it near  
heat sources.  
! The appliance was designed and manufactured in compliance  
with international safety standards. The following warnings are  
provided for safety reasons and must be read carefully.  
• Try to avoid keeping the door open for long periods or opening  
the door too frequently in order to conserve energy.  
• Do not fill the appliance with too much food: cold air must  
circulate freely for food to be preserved properly. If circulation  
is impeded, the compressor will work continuously.  
• Do not place hot food directly into the refrigerator. The internal  
temperature will increase and force the compressor to work  
harder and will consume more energy.  
• Defrost the appliance if ice forms (see Maintenance). A thick  
layer of ice makes cold transference to food products more  
difficult and results in increased energy consumption.  
• The temperature inside the freezer is too high. The freezer will  
maintain a temperature of around 0°C so that the food will not  
refreeze, allowing you to eat it within 24 hours or to refreeze it  
after it has been cooked.  
This appliance complies with the following Community Directives:  
- 73/23/EEC of 19/02/73 (Low Voltage) and subsequent amendments;  
-89/336/EEC of 03.05.89 (Electromagnetic Compatibility) and  
subsequent amendments;  
- 2002/96/CE.  
General safety  
• The appliance was designed for domestic use inside the home  
and is not intended for commercial or industrial use.  
• The appliance must be used to store and freeze food products  
by adults only and according to the instructions in this manual.  
• The appliance must not be installed outdoors, even in covered  
areas. It is extremely dangerous to leave the appliance  
exposed to rain and storms.  
To switch off the buzzer, open and close the appliance door  
or press the + and – freezer temperature adjustment buttons  
once. Press these buttons a second time to display the set  
value on the freezer display, switch off the TEMPERATURE  
ALARM LED and restore normal operation.  
• Do not touch the appliance with bare feet or with wet or moist  
hands and feet.  
• Do not touch the internal cooling elements: this could cause  
skin abrasions or frost/freezer burns.  
• When unplugging the appliance always pull the plug from the  
mains socket, do not pull on the cable.  
Before cleaning and maintenance, always switch off the  
appliance and disconnect it from the electrical supply. It is  
not sufficient to set the temperature adjustment knobs on  
OFF(appliance off) to eliminate all electrical contact.  
• In the case of a malfunction, under no circumstances should  
you attempt to repair the appliance yourself. Repairs carried  
out by inexperienced persons may cause injury or further  
malfunctioning of the appliance.  
• Do not use any sharp or pointed utensils or electrical equipment  
- other than the type recommended by the manufacturer - inside  
the frozen food storage compartments.  
• Do not put ice cubes taken directly from the freezer into your  
mouth.  
• This appliance is not intended for use by persons (including  
children) with reduced physical, sensory or lack of experience  
and knowledge unless they have been given supervision  
or instruction concerning use of the appliance by a person  
responsible for their safety. Children should be supervised to  
ensure that they do not play with the appliance.  
• Keep packaging material out of the reach of children! It can  
become a choking or suffocation hazard.  
Disposal  
• Observe local environmental standards when disposing  
packaging material for recycling purposes.  
• The European Directive 2002/96/EC on Waste Electrical and  
Electronic Equipment (WEEE), requires that old household  
electrical appliances must not be disposed of in the normal  
unsorted municipal waste stream. Old appliances must be  
collected separately in order to optimise the recovery and  
recycling of the materials they contain and reduce the impact  
on human health and the environment. The crossed out  
“wheeled bin” symbol on the product reminds you of your  
obligation, that when you dispose of the appliance it must be  
separately collected. Consumers should contact their local  
authority or retailer for information concerning the correct  
disposal of their old appliance.  
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR 5 YEAR PARTS GUARANTEE ON 08448 24 24 24  
7
 
19511505801  
12/2013  
Troubleshooting  
GB  
If the appliance does not work, before calling for Assistance (see  
Assistance), check for a solution from the following list.  
The internal light does not illuminate.  
• The plug has not been inserted into the electrical socket, or not  
far enough to make contact, or there is no power in the house.  
The refrigerator and the freezer do not cool well.  
• The doors do not close properly or the seals are damaged.  
• The doors are opened too frequently.  
• The TEMPERATURE ADJUSTMENT knob is not in the correct  
position.  
• The refrigerator or the freezer have been over-filled.  
• The atmospheric temperature of the area surrounding the  
appliance is lower than 14°C.  
The food inside the refrigerator is beginning to freeze.  
• The TEMPERATURE ADJUSTMENT knob is not in the correct  
position.  
• The food is in contact with the back inside wall of the  
refrigerator.  
The AIR fan does not rotate  
• The refrigerator door is open.  
• The AIR system is only activated automatically when it becomes  
necessary to restore perfect operational conditions inside the  
refrigerator compartment.  
The motor runs continuously.  
• The door is not closed properly or is continuously opened.  
• The outside ambient temperature is very high.  
• The thickness of the frost exceeds 2-3 mm (see Maintenance).  
The appliance makes a lot of noise.  
• The appliance has not been installed on a level surface (see  
Installation).  
• The appliance has been installed between cabinets that vibrate  
and make noise.  
• The internal refrigerant makes a slight noise even when the  
compressor is off. This is not a defect, it is normal.  
Some of the external parts of the refrigerator become hot.  
• These raised temperatures are necessary in order to avoid the  
formation of condensation on certain parts of the product.  
The back wall of the refrigerator unit is covered in frost or  
droplets of water  
• This shows the appliance is operating normally.  
There is water at the bottom of the refrigerator.  
• The water discharge hole is blocked (see Maintenance).  
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR 5 YEAR PARTS GUARANTEE ON 08448 24 24 24  
8
 

Grundig CRT Television AMIRA26HDBLK User Manual
Haicom Recording Equipment HI 602 User Manual
Haier Refrigerator 16 User Manual
HANNspree Flat Panel Television DT04 12U1 User Manual
HANNspree Flat Panel Television K215 10A1 User Manual
Hotpoint Oven SC77E User Manual
Hotpoint Range DSD 60 S S User Manual
Husqvarna Brush Cutter 53 5RJ User Manual
Husqvarna Saw K650 User Manual
Hypertec Camera Accessories D7978KHY User Manual