Haier Washer Dryer HWM130 0713S User Manual

Twin-tub Washing Machine  
User's manual  
This manual is for  
HWM130-0713S  
Please read this manual  
carefully before using.  
0030807922A  
Retain it for future reference.  
 
Names of the parts  
Drain selector  
Wash selector  
Wash timer  
Outer cover of the spin tub  
Inner cover of the spin tub  
Water-filling entrance  
Inlet selector  
Control panel  
Spin timer  
Filter frame  
Water level adjusting lever  
Major frame  
Lint filter  
Spin tub  
Wash tub  
Valve cover  
Cabinet  
Pulsator  
Wash tub cover  
Drain hose  
Base frame  
Notes: All illustrations in this manual are given for reference only. Your products and  
accessories may show differences from these illustrations due to our  
continuous improvement.  
Meaning and description of the symbols  
Contents marked with that symbol are related  
Warning sign  
to the safety of the product and the personal  
safety of the users. Please operate in strict  
conformity to the contents, otherwise it may  
cause damage of the machine or injure the  
personal safety of the user.  
Contents marked with that symbol are actions  
Forbidding sign  
forbidden to perform. Performing of those  
actions may result in damage of the machine  
or injure the personal safety of the user.  
Please check if the power receptacle has good earthing condition  
before using to guarantee your safety.  
1
 
Safety precautions  
Please insert the power cord into  
special receptacle with rated vol-  
tage. Be sure to use single-phase  
three pins receptacle. The earthing  
terminal of the receptacle must be  
earthed reliably. If possible, please  
adopt electric leakage protector.  
When the machine is normally  
using, please put the power plug  
at the location easily to be insert-  
ed and extracted by hand. Be sure  
to pull the plug off when there's  
power failure, or the machine is  
being moved, cleaned or when it  
is idle.  
If the power cord is bad, to avoid risk it is required to replace it by the  
technicians of our special shop or the after-sale service department.  
Keep the pin of the power plug clean.  
Do not put the machine at damp  
place like the bathroom . Never  
wash it with water. Do not place  
wet laundries on the control panel.  
Do not use water hotter than 50 C .  
In case the washing machine is installed  
on ground with carpet , do not block the  
ventilation hole with carpet.  
Do not wash water-proof laundries like  
the raincoat, bike covers etc. to avoid  
abnormal vibrations in spinning.  
Ventilation hole at  
the bottom of the  
washing machine  
Do not let the machine share one receptacle  
with other electric appliances. If the power  
plug is damaged, or the plugging into the  
receptacle is loose, do not use the plug any  
more.  
2
 
Safety precautions  
Do not stretch hands into the working  
machine. It is dangerous even if the  
rotation is slow. Take special care of  
the children.  
Do not decompose, repair or alter the  
machine by yourself.  
Do not put any hot or heavy items  
( such as the kettle with hot water )  
on the washing machine.  
Do not wash laundries with volatile  
materials (such as thinner, petrol etc.).  
etrol  
P
inner  
Th  
Keep the machine away from direct  
sunlight and heat source like the  
heater.  
Handicapped or children without care  
shall not use the machine.  
Please put down the drain hose before washing and connect the water inlet pipe properly.  
It is suggested to use foamless washing powder.  
Please don t use the washer in the environment below 0 C. If the washer is below 0 C, the  
washer s water inlet system and draining system will be frozen ,then result in the damaged  
of the whole machine. If the washer has below 0 C, please be sure to ensure the washer is  
placed under the room temperature for 2~4 hours and then use .  
3
 
Installation and adjustment  
Please install and adjust the machine according to the requirement of  
the manual. It is very important to your security and correct operating  
the machine.  
Usage of the drain hose  
The drainage shall be smooth with the drain hose.  
<10cm  
1.The height of the drain hose shall be  
less than 10cm , or the drainage will  
not be smooth enough and cause  
incomplete drainage.  
2.Do not tramp or press the drain hose.  
3.If the drain hose is too long, cut it at mid point.  
To make smooth drainage, cut the front end of  
the hose slantingly.  
>
30mm  
4.If extra drain hose is needed , please make  
separate purchase. The inner diameter of the  
extra hose shall not less than 30mm, and the  
length shall not exceed 1.5m.  
<1.5m  
If the extra hose is too long, cut it either  
at point A or B.  
A
B
Voltage change  
This washer is assembled for 220V, but can be changed from 220V to 127V.  
Check your electrical source and follow the diagram below to convert voltage.  
Green  
Blue  
White  
(1). Loosen the fastening screw and take off the back cover.  
(2). Unknit the safeguard bag to expose the connectors.  
(3). Detach the white connector from the green one(220V), then inlay  
it into the blue one(127V).  
(4). Pack all the connectors with the safeguard bag as usual and fix it.  
Then install the back cover.  
Above all the steps must be done by the special serviceman.  
4
 
Install the lint filter  
Put the underside of the lint filter into overflow filter  
then push the upside into overflow filter.  
overflow filter  
lint filter  
After installation, please refer that the lint filter  
installed to the right station, otherwise the lint  
filter may be fallen off when washing, influencing  
your use.  
How to change the direction of the drain hoses  
Back  
Figure 1 indicates the ex factory installation  
position of the drain hose.  
Soft item  
Front  
Extend the drain hose from the side of spin tub  
Figure 1  
Put soft items on the ground. Lean the machine  
down gently with the front surface facing the  
ground. Take off the drain hose from the cabinet.  
Take the hose out of the fixing groove.  
(See to Figure 2).  
Figure 2  
Soft item  
Embed the drain hose into the groove along the  
side of the spin tub in the order of (1)~(3), heading  
for the side of the spin tub. (See to Figure 3).  
Embed the drain hose into the groove with  
hands. Take care not to damage the drain  
hose in fastening the fixing clamp.  
Extend to the  
spin tub side  
Embed into the  
groove in turn  
Figure 3  
Install the water inlet hose; Select the water level  
Insert the water inlet hose into the water-fillingWater inlet hose  
entrance on the control pane directly.(pull it  
out to dismantle it)  
Water inlet  
Water level  
indicator  
Select water level according to the  
quantity of the laundries.  
Set the water level adjusting lever  
to needed line.  
Max  
Maximum  
Med  
Medium  
Min  
Minimum  
5
 
Preparation before washing  
Preparation before washing  
1.Connect the water inlet hose.  
2.Confirm that the washing machine is earthed  
reliably . Then insert the power plug into the  
receptacle. Do not connect the earth terminal  
to the gas pipe and tap water pipe.  
3.Put down the drain hose .  
4.Slanting or uneven ground may result in  
unstable working or abnormal noise. Please  
make the machine stand horizontally.  
Pay attention to followings before washing the laundries  
Check if  
When the pulsator  
is running , the  
buttons of the  
laundries may  
cause noise. For  
the sake of  
discretion, please  
put the laundries  
with buttons into  
other laundries.  
Clear the  
The quantity of  
the laundries  
shall not be too  
large. Stretch  
and loosen the  
laundries before  
putting them in  
the tub.  
Tie the long  
strips; fasten  
the buttons;  
close zippers.  
the laundries  
has special  
requirement  
on washing  
pocket. Take  
out the coins,  
sand, hairpins  
etc.  
a. Check if the laundries are applicable for washing with machine.  
b. Divide the laundries that are not colorfast from other laundries.  
c. Put those laundries difficult to absorb water into water with hand.  
d. For those laundries with heavy soil, please first remove the dirt like  
mud or dust. For the parts with heavy soil, please apply detergent on  
them in advance, which can make it easier to remove the soil.  
e. For those laundries that may get lint ball and those with long fur, turn  
it over before putting in.  
f. Do not put those laundries polluted by chemicals into the washing  
machine directly.  
6
 
The musts in washing  
The capacity of washing and spinning of the  
machine refer to the largest weight of the  
standard laundries under dry condition that can  
be washed or spinned in one time. Laundries  
quantity in one washing cycle shall be lower  
than the rated capacity.  
The thickness ,size , type of the cloth will influ-  
ence the actual washing capacity. It is suit-  
able to put in reasonable amount of laundries  
and the laundries can be turned round in wash-  
ing for one time washing.  
Do not select " Maximum " water level for  
laundries less than 1.0kg, so as to avoid  
splashing of water.  
Usage of the detergent  
How to use the washing powder  
How to use the whitener  
Direct dissolved in the machine:  
1.Fill small quantity of water.  
2.Add the powder . Run for 30  
seconds to dissolve it completely.  
3.Put it in the laundries. Select suitable  
water level.  
Fill water to decided level. Dilute  
the whitener with container.  
Pour it slowly into the washing tub.  
Avoid using whitener on laun-  
dries with color or pattern as they  
are prone to lose color.  
The instant dissolving of the washing  
powder:  
1.Prepare warm water of 30 C and a  
container.  
2.Add the powder while stirring to fully  
dissolve it.  
The whitener shall not touch  
the laundries directly.  
Refer to the user's manual for  
the usage and quantity of the  
whitener.  
The powder is more prone to pollute the  
laundries than the detergent. Therefore  
please use it with proper quantity.  
For powder whitener, please  
dissolve it before using.  
Dosage of different washing powder is  
different. Please refer to the instruction  
of the washing powder for the detail  
dosage.  
7
 
Washing sequence  
Wash timer  
Wash selector  
Spin timer  
Drain selector  
Inlet selector  
(To set to below 1 minute,  
first set to 2 minute then  
turn it back. it can increase  
the service life of the timer).  
(To set to below 2 minute,  
first set to 6 minute then  
turn it back. it can increase  
the service life of the timer).  
(Do not set drain selector  
on Drain position during  
washing)  
(Standard current,  
strong current)  
OFFF  
OFF  
1
2
5
3
6
15  
12  
DRAIN  
4
WASH  
SPIN  
3
9
SPIN TIMER  
WASH SELECTOR  
DRAIN SELECTOR  
WASH TIMER  
Wash  
WASH  
SPIN  
1 Inlet selector  
(1) Set fill selection to Wash side .(Figure 1)  
(2 )Adjust water level rod to a position as needed.  
Figure 1  
2
Fill water and add solved powder detergent until  
water reaches a suitable level.(Figure 2)  
It begin to wash to dispense detergent uniformly.  
Figure 2  
Figure 3  
STRONG  
3
4
Put in the wash load, and supplement water  
as necessary.  
STANDARD  
Select the current  
WASH SELECTOR  
Select the strength of the current according to  
the laundries. (Figure 3)  
OFF  
3
15  
5
Select the washing time  
Select the washing time according to the  
6
12  
laundries. (Figure 4)  
WASH TIMER  
9
Figure 4  
OFF  
6
After washing,set the DRAIN SELECTOR  
at DRAIN .(Figure 5)  
DRAIN  
Figure 5  
DRAIN SELECTOR  
8
 
Midway spinning  
1.Put the laundries into the spin tub evenly and smoothly.  
2.Spin  
(1) Put the gland in properly.  
Please put in the gland properly even if the  
laundries quantity is small.  
Push  
Gland  
Push  
Proper  
Proper  
The laundries  
are slanting  
No gland  
(2) Close the inner and outer cover of the spin tub.  
Outer cover of  
The spin tub  
Inner cover of  
The spin tub  
(3) Spin for 1-2 minutes.  
3.Run the foam-removing spinning.  
(1) Open the outer cover of the spin tub.  
(2) Set the water-filling selector control  
rod at the "SPIN" side. Fill water for  
about 1 minute.  
WASH  
SPIN  
If the water quantity filled is too large,  
the water may flow out from the wash  
tub side. Please twist the water tap to  
limit the water filling.  
(3) Close the outer cover of the spin tub.  
Spin for 1-2 minutes.  
9
 
Rinsing  
Rinse with water-filling  
1.Put the laundries into the wash tub. Select  
suitable current according to the laundries.  
2.Adjust the water level  
Set the water level with water level adjusting  
lever according to the laundries quantity.  
Then fill suitable water continuously.  
3.Rinse  
Adjust the wash timer to 5-7 minutes to do  
rinsing.  
(Repeat the midway spinning and  
rinsing with stored water for 2-3 times)  
Rinse with stored water  
1. Put the laundries into the wash tub. Select suitable current according to  
the laundries.  
2. Fill water to preset water level.  
3. Rinse  
Adjust the wash timer to 2-3 minutes to do rinsing.  
When the laundries quantity is a few , please use "Standard" current.  
If you use "Strong" current, it may splash.  
10  
 
Spinning  
1. Put the laundries into the spin tub  
evenly and smoothly.  
2. Press the gland in the tub properly.  
Close the inner and outer cover of  
the spin tub.  
3. Spin  
Select suitable spin time according  
to the laundries, and do spinning.  
During spinning, if there's abnormal  
sound, it is generally owing to slanting  
placement of the laundries. Please  
stop the machine and re-order the  
laundries.  
In spinning, it will pause the work if you open the outer cover of the spin  
tub. Close it to resume the spinning.  
To do spinning and draining  
or rinsing with water-filling  
together, please first do  
spinning for around 1 minute,  
then do draining or rinsing  
with water-filling. Otherwise  
the spinning will stop owing  
to too much water stored in  
the spin tub.  
11  
 
Disposal after washing  
After using, please clean the lint and foreign materials of the lint filter and  
overflow filter in time. Otherwise it may influence your using the machine.  
Please first pull off the power plug from the receptacle before cleaning.  
Cleaning the lint filter  
The lint filter must be used during washing.  
It must be cleaned in time after each using.  
1. Press the elastic piece at upper end of lint filter to  
release the tab from the filter cover, and pull the lint  
filter outward to remove it. (See Figure 1).  
Figure 1  
2. Remove lint  
Pull the lower end of lint filter rear cover outward  
to disassemble it from the lint filter front cover.  
Lint filter rear cover  
Remove lint completely with clear water. (See  
Figure 2).  
Disassemble  
Assemble  
3. Install lint filter  
Lint filter front cover  
Page 4  
Figure 2  
Cleaning the overflow filter  
Too much lint on the overflow filter will influence  
the normal usage of the machine. Please  
clean it every two months.  
Elastic fixing  
claw  
1
Take off the overflow filter.  
As indicated in the figure, nip the elastic fixing  
claw and pull it to the direction of the arrow to  
take it off.  
12  
 
Cleaning the overflow filter  
2. Take off the corrugation pipe.  
Dismantle the upper part of the  
corrugation pipe inside the  
overflow filter ( as indicated in  
Figure 1).  
Water level  
adjusting lever  
Corrugation  
pipe  
3. Cleaning the overflow filter  
Clean the lint around the filter  
and flush with tap water.  
Figure 1  
4. Install the overflow filter.  
(1).Install the corrugation pipe.  
(2).Insert the mounting plate at  
the bottom of the filter into  
the valve cover.  
Hook  
(3).Hang up the hook at  
upper side.  
Figure 2  
(4).Push the upper part in as  
indicated in Figure 2.  
Disposal of the complete unit  
After washing, dismount the water inlet  
hose.  
Do not store water in the tub for long  
period. Discharge the water immediately  
after each using.  
Pull off the power plug and hang up the  
power cord.  
Hang up the drain hose.  
Wipe the complete unit with soft  
cloth twisted dry.  
Wipe with neutral detergent if too dirty  
Do not wash it directly by water  
Wipe off the water drops on the surface  
and inside the tub with clean soft cloth.  
Open the cover of the wash tub and the  
inner/outer cover of the spin tub for  
some time (about one hour), then close  
them.  
Petrol  
Thinner  
Alcohol  
13  
 
Trouble-shooting Answer to question  
If the laundries fall to the outer side of the spin tub  
If the laundries fall to the outer side of the spin tub,  
please take them out immediately.  
When the remained water is frozen  
Prevent the freezing (be sure to discharge the water  
completely after using)  
After complete draining, set the "DRAIN SELECTOR"  
at "OFF" . If it is set at "DRAIN", it will be rather difficult  
for the frozen water to melt.  
Below 50 c  
2~3L  
When the water is frozen  
Pour hot water below 50  
into the wash tub  
to soak it completely. Then turn the pulsator  
with hands gently. Please confirm the drainage  
can work normally before next using.  
14  
 
Trouble-shooting Answer to question  
(If there's breakdown, please pull off the power plug before checking) The following  
phenomena are not breakdowns sometimes. Please confirm again before sending  
it to repair. If there are real breakdowns, please come to the special maintenance  
department or after-sale service department of our company. Do not repair it by yourself.  
Phenomena  
The reason  
Is there power failure?  
Is the power plug loose?  
Is the pulsator twisted by foreign materials?  
The machine does  
not act.  
Is the drain hose put down?  
Is the drain hose frozen?  
Is the drain hose blocked by foreign material?  
Are there laundries falling to the outer side of  
the spin tub?  
The draining does not  
work  
There's abnormal  
sound during washing  
Are there hair pin, coins or metal items brought  
inside the tub?  
Is the machine slanting?  
There's abnormal  
sound and violent  
vibration during  
spinning  
Is the gland pressed evenly?  
Are there laundries falling to the outer side of  
the spin tub?  
Are the laundries in spin tub too much?  
There may be some  
water flowing out of  
the drain hose in the  
first use of the  
It is the water remained in the factory inspection  
of performance.  
machine.  
15  
 
Packing list  
Quantity  
One piece  
Name  
User's manual  
One piece  
Water inlet hose  
One piece  
One set  
Gland  
Twin-tub washing machine  
Specification  
Water level / Water quantity (about)(L) Maximum/89L Medium/75L Minimum/63L  
Rated washing capacity kg  
Rated spinning capacity kg  
Injection pressure(MPa)  
10.0  
6.0  
0.02~0.2  
270/340  
Rated washing power(W)  
Rated spinning power(W)  
125/180  
Made in China  
16  
 

Great Dane Lawn Mower GSKH1848S User Manual
Grundig MP3 Player 30GB User Manual
Haier Coffeemaker HCS10B User Manual
Haier Microwave Oven EO 2080EGV User Manual
Honeywell Smoke Alarm IPGSM DP User Manual
HP Hewlett Packard Server 669322 B21 User Manual
HP Hewlett Packard Switch 3500yl Series User Manual
Hunter Fan Outdoor Ceiling Fan 26106 User Manual
IBM Switch BM 8270 User Manual
Igloo Water Dispenser MWC529 User Manual