Fujitsu Network Card FMC 16FX FAMILY User Manual

Fujitsu Microelectronics Europe

FMEMCU-UG-960011-10

User Guide

F²MC-16FX FAMILY

ADAPTER BOARD

ADA-16FX-ETHERNET

USER GUIDE

ADA-16FX-ETHERNET

Warranty and Disclaimer

To the maximum extent permitted by applicable law, Fujitsu Microelectronics Europe GmbH restricts

its warranties and its liability for the ADA-16FX-ETHERNET Board and all its deliverables (eg.

software include or header files, application examples, target boards, evaluation boards, engineering

samples of IC’s etc.), its performance and any consequential damages, on the use of the Product in

accordance with (i) the terms of the License Agreement and the Sale and Purchase Agreement under

which agreements the Product has been delivered, (ii) the technical descriptions and (iii) all

accompanying written materials. In addition, to the maximum extent permitted by applicable law,

Fujitsu Microelectronics Europe GmbH disclaims all warranties and liabilities for the performance of

the Product and any consequential damages in cases of unauthorised decompiling and/or reverse

engineering and/or disassembling. Note, the ADA-16FX-ETHERNET Board and all its deliverables

are intended and must only be used in an evaluation laboratory environment.

Fujitsu Microelectronics Europe GmbH warrants that the Product will perform substantially in

accordance with the accompanying written materials for a period of 90 days form the date of

receipt by the customer. Concerning the hardware components of the Product, Fujitsu

Microelectronics Europe GmbH warrants that the Product will be free from defects in material

and workmanship under use and service as specified in the accompanying written materials

for a duration of 1 year from the date of receipt by the customer.

Should a Product turn out to be defect, Fujitsu Microelectronics Europe GmbH´s entire liability

and the customer’s exclusive remedy shall be, at Fujitsu Microelectronics Europe GmbH´s

sole discretion, either return of the purchase price and the license fee, or replacement of the

Product or parts thereof, if the Product is returned to Fujitsu Microelectronics Europe GmbH in

original packing and without further defects resulting from the customer’s use or the transport.

However, this warranty is excluded if the defect has resulted from an accident not attributable

to Fujitsu Microelectronics Europe GmbH, or abuse or misapplication attributable to the

customer or any other third party not relating to Fujitsu Microelectronics Europe GmbH.

To the maximum extent permitted by applicable law Fujitsu Microelectronics Europe GmbH

disclaims all other warranties, whether expressed or implied, in particular, but not limited to,

warranties of merchantability and fitness for a particular purpose for which the Product is not

designated.

To the maximum extent permitted by applicable law, Fujitsu Microelectronics Europe GmbH´s

and its supplier’s liability are restricted to intention and gross negligence.

NO LIABILITY FOR CONSEQUENTIAL DAMAGES

To the maximum extent permitted by applicable law, in no event shall Fujitsu

Microelectronics Europe GmbH and its suppliers be liable for any damages whatsoever

(including but without limitation, consequential and/or indirect damages for personal

injury, assets of substantial value, loss of profits, interruption of business operation,

loss of information, or any other monetary or pecuniary loss) arising from the use of

the Product.

Should one of the above stipulations be or become invalid and/or unenforceable, the remaining

stipulations shall stay in full effect

- 3 -

UG-960011-10

ADA-16FX-ETHERNET

Chapter 1 Contents

1 Contents

REVISION HISTORY............................................................................................................ 2

WARRANTY AND DISCLAIMER ......................................................................................... 3

1 CONTENTS...................................................................................................................... 4

2 OVERVIEW...................................................................................................................... 5

2.1 Abstract................................................................................................................... 5

2.2 Features of adapter board ADA-16FX-ETHERNET v1.1 ......................................... 5

2.3 Features supported by base board SK-16FX-EUROSCOPE (SK-16FX-100PMC) .. 5

3 INSTALLATION............................................................................................................... 6

3.1 Jumper settings of ADA-16FX-ETHERNET v1.1 ..................................................... 7

4 JUMPERS AND LED’S.................................................................................................... 8

4.1 Chip select (JP: 1, 2, 3) ........................................................................................... 8

4.2 Ethernet jack Select (JP: 4, 5) ................................................................................. 8

4.3 Link LED, Activity LED (LINK, ACT) ........................................................................ 9

5 CONNECTORS.............................................................................................................. 10

5.1 Ethernet connector (X1) ........................................................................................ 10

5.2 Edge Connectors (X2, X3, X11) ............................................................................ 10

6 SILK-PLOT OF THE BOARD ........................................................................................ 11

7 RELATED PRODUCTS ................................................................................................. 12

8 INFORMATION IN THE WWW....................................................................................... 13

UG-960011-10

- 4 -

ADA-16FX-ETHERNET

Chapter 2 Overview

2 Overview

2.1 Abstract

The ADA-16FX-ETHERNET is an adapter board that can be used together with the

evaluation board SK-16FX-EUROSCOPE (SK-16FX-100PMC). The ADA-16FX-ETHERNET

extends the evaluation board with Ethernet connectivity. It can be used for software

development and testing.

The board allows the designer immediately to start with the software development before a

final target system is available.

2.2 Features of adapter board ADA-16FX-ETHERNET

< 10BaseT Ethernet connectivity

< Software example including openTCP stack is available

< Multiplexed bus interface

< Selectable chip select via Jumper

< Pin header for SK-16FX-EUROSCOPE (SK-16FX-100PMC) base board

(Note: SK-16FX-EUROSCOPE has to be ordered separately)

2.3 Features of base board SK-16FX-EUROSCOPE (SK-16FX-100PMC)

< 1x UART-Transceiver (SUB-D9 connector)

< 1x USB to serial converter (Type-B connector)

< 1x High-speed CAN-Transceiver (SUB-D9 connector)

< 2x LED-Display (7-Segment)

< 2x User-button

< 1x Reset-button, Reset-LED

< All 100 pins routed to pin-header

< On-board 5V and 3V voltage regulators, Power-LED

< USB power-supply (external power supply possible)

This board must only be used for test applications

in an evaluation laboratory environment.

- 5 -

UG-960011-10

ADA-16FX-ETHERNET

Chapter 3 Installation

3 Installation

Remove carefully the board from the shipping box and check for any damages.

Disconnect your SK-16FX-EUROSCOPE (SK-16FX-100PMC) evaluation board from USB

and external power supply. Select the correct Voltage supply:

ADA-16FX-ETHERNET is designed for 5V power supply.

Jumper

Setting

1-2

Description

VCC is set to 5V (ADA-16FX-ETHERNET)

VCC is set to 3.3V

JP10 (5V/3V3)

2-3

Attach the adapter board to the evaluation board as shown below. The Ethernet jack has to

face to the outer edge.

Ethernet jack

Note:

Make sure to jumper the board to 5V before connecting the ADA-16FX-ETHERNET.

UG-960011-10

- 6 -

ADA-16FX-ETHERNET

Chapter 3 Installation

3.1 Jumper settings of ADA-16FX-ETHERNET

The following jumper settings are set by default:

Jumper

Description / Function

Type

Default

JP1

JP2

JP3

JP4

JP5

Use chip select line 2

Use chip select line 3

solder JP 2pol. Closed

solder JP 2pol.

solder JP 3pol.

Open

1-2

Use chip select line 4

Select center tap A of Ethernet jack

Select center tap B of Ethernet jack

1-2

Please refer to the documentation of the evaluation board for detailed information about the

jumper settings for the SK-16FX-EUROSCOPE (SK-16FX-100PMC).

- 7 -

UG-960011-10

ADA-16FX-ETHERNET

Chapter 4 Jumpers and LED’s

4 Jumpers and LED’s

This chapter describes all jumpers that can be modified and all LED’s on the adapter board.

The default setting is shown with a grey shaded area.

4.1 Chip select (JP: 1, 2, 3)

One out of the three chip select signals CS2, CS3 or CS4 can be selected:

JP1, JP2, JP3 connect chip select signal of MCU to chip select signal of Ethernet chip

Jumper

Setting

Description

ON (closed)

OFF (open)

ON (closed)

OFF (open)

ON (closed)

OFF (open)

CS2 is connected to CHIPSEL of CS8900A

CS2 is not connected

JP1 (CS2)

CS3 is connected to CHIPSEL of CS8900A

CS3 is not connected

JP2 (CS3)

JP3 (CS4)

CS4 is connected to CHIPSEL of CS8900A

CS4 is not connected

Default: JP1 is closed

By default, the chip select signal CS2 of the MB96F348HS is connected to the Ethernet chip.

4.2 Ethernet jack select (JP: 4, 5)

The board layout is designed to be used with different Ethernet jacks.

JP4, JP5

Select center tap pin of Ethernet jack

Jumper

Setting

Description

1-2

Capacitor 9 is connected to pin 4 of the

Ethernet jack

JP4 (AVss)

2-3

1-2

2-3

Capacitor 9 is connected to pin 7 of the

Ethernet jack

Capacitor 10 is connected to pin 5 of the

Ethernet jack

JP5 (AVcc)

Capacitor 10 is connected to pin 8 of the

Ethernet jack

Default: JP4 and JP5 are set to 1-2

By default the pins 4 and 5 of the assembled Ethernet jack are used as center tap pin. This

setting depends on the type and manufacturer of the used Ethernet jack (see chapter 5.1).

UG-960011-10

- 8 -

ADA-16FX-ETHERNET

Chapter 4 Jumpers and LED’s

4.3 Link LED, Activity LED (LINK, ACT)

These LEDs display the status of the Ethernet interface.

LED

LINK

ACT

Colour

Green

Yellow

Description

Indicates that a link is established

Indicates activity on the Ethernet

By default the LINK LED should light directly after connected to a network.

- 9 -

UG-960011-10

ADA-16FX-ETHERNET

Chapter 5 Connectors

5 Connectors

5.1 Ethernet connector (X1)

This is the Ethernet jack for connecting the ADA-16FX-ETHERNET to the Ethernet. The

connector complies with the 10BaseT standard. The used connector has integrated

transformers for transmit and receive lines.

The Ethernet jack and the Ethernet controller depends on the power supply voltage:

Supply Voltage

Used jack

Ethernet Chip Adapter Board

Transitions Transitions

Halo HFJ11-

1043E

ADA-16FX-

CS8900CQZ

1:1

1:1.41

1:2.5

ETHERNET

Halo HFJ11-

1041E

3V3

CS8900CQ3Z

5.2 Edge Connectors (X2, X3, X11)

The edge connectors are assembled on the bottom side of the adapter board. They are used

to attach the ADA-16FX-ETHERNET adapter board to the SK-16FX-EUROSCOPE (SK-

16FX-100PMC) evaluation board. All used signals are provided by the edge connectors.

Connector

X2 (1 – 20)

MCU Pins

1 – 20

X3 (71 – 100)

X11 (51 – 70)

71 – 100

51 – 70

The adapter board is powered via the edge connectors.

UG-960011-10

- 10 -

ADA-16FX-ETHERNET

Chapter 6 Silk-Plot of the Board

6 Silk-Plot of the Board

Ethernet

connector

Latch

Cirrus

CS8900A

X11

- 11 -

UG-960011-10

ADA-16FX-ETHERNET

Chapter 7 Related Products

7 Related Products

SK-16FX-EUROSCOPE

ADA-16FX-ETHERNET

MB96F348HS

Evaluation board with MB96F348HS

FPT-100P-M20 package

Adapterboard for SK-16FX-EUROSCOPE

(SK-16FX-100PMC)

MB96340 Series Flash MCU

UG-960011-10

- 12 -

ADA-16FX-ETHERNET

Chapter 8 Information in the WWW

8 Information in the WWW

Information about FUJITSU MICROELECTRONICS Products

can be found on the following Internet pages:

Microcontrollers (8-, 16-, and 32bit), Graphics Controllers

Datasheets and Hardware Manuals, Support Tools (Hard- and Software)

http://mcu.emea.fujitsu.com

Linear Products: Power Management, A/D and D/A Converters

http://www.fujitsu.com/emea/services/microelectronics/linears/

Media Products: SAW filters, acoustic resonators and VCOs

http://www.fujitsu.com/emea/services/microelectronics/saw/

For more information about FUJITSU MICROELECTRONICS

http://www.fujitsu.com/emea/services/microelectronics/

- 13 -

UG-960011-10

ADA-16FX-ETHERNET

Chapter 8 Information in the WWW

Recycling

Gültig für EU-Länder:

Gemäß der Europäischen WEEE-Richtlinie und deren Umsetzung in landesspezifische

Gesetze nehmen wir dieses Gerät wieder zurück.

Zur Entsorgung schicken Sie das Gerät bitte an die folgende Adresse:

Fujitsu Microelectronics Europe GmbH

Warehouse/Disposal

Monzastraße 4a

63225 Langen

Valid for European Union Countries:

According to the European WEEE-Directive and its implementation into national laws we

take this device back.

For disposal please send the device to the following address:

Fujitsu Microelectronics Europe GmbH

Warehouse/Disposal

Monzastraße 4a

D-63225 Langen

Germany

UG-960011-10

- 14 -

Edelbrock Automobile Parts 1926 User Manual
Everpure Water System CG53 10 User Manual
Extron electronic Speaker System SI 3 Black User Manual
Extron electronic Switch FLS 101 User Manual
Fedders Humidifier AC1A Series User Manual
Fisher Price Building Set C5792 User Manual
FujiFilm Camera Lens YF4A SA2B User Manual
Gardena Trimmer THS 400 User Manual
GE Air Conditioner ASW18 User Manual
Gianni Industries Door Electromagnetic Lock User Manual