Edelbrock Automobile Parts Non EGR for Chevrolet 90 V6 User Manual

PERFORMER MANIFOLD  
MODEL: Non-EGR for Chevrolet 90° V6, 4.3L Vortec  
CATALOG #2114  
®
INSTALLATION INSTRUCTIONS  
Please study these instructions carefully before installing your new manifold. If you have any questions or problems,  
please call our Technical Hotline at: 1-800-416-8628, 7:00 am to 5:00 pm, Monday - Friday, Pacific Standard Time or  
e-mail us at [email protected].  
EGR SYSTEM: This manifold will not accept stock EGR (exhaust gas recirculation) equipment. Not legal on pollution-  
controlled motor vehicles.  
MANIFOLD: This manifold will not accept any O.E.M. carburetor systems. We suggest you use the carburetor listed in  
the carburetor recommendations. This manifold was designed for street rod, off-road and marine applications.  
ACCESSORIES & INSTALLATION ITEMS: Major recommendations are listed below. Please review each part listed  
in the Installation Items section of the Edelbrock catalog to decide whether more items are required for your specific vehicle  
than are mentioned in these instructions.  
MARINE APPLICATIONS: This manifold has been designed to accept either MerCruiser or OMC waterneck housings  
using the lateral bolt holes of the waterneck flange in the manifold. Because of carburetor interference, the use of a 1"  
high divided carb spacer (such as Edelbrock #8714) may be necessary. Waterneck housings vary, so determine if spacer  
is needed prior to installation. If marine carburetor #1409 is used, you must re-calibrate the carburetor with Calibration Kit  
#1485. NOTE: Salt water will corrode coolant passageway of manifold and greatly shorten manifold service life.  
CARBURETOR RECOMMENDATIONS: Use only carburetors recommended. If parts required for installation are  
unavailable locally, contact Edelbrock directly.  
CARBURETOR  
REFERENCE  
PARTS REQUIRED FOR INSTALLATION  
Performer #1403 (500 cfm)  
Performer #1404 (500 cfm)  
Performer #1409 (600 cfm)  
A, F, I, K (for 4.3L only)  
A, F, I, K (for 4.3L only)  
A, F, I (for 4.3L Marine only)  
(none)  
(none)  
#1485 Calibration Kit for Marine Applications  
A - Carburetor will work with non-EGR (Exhaust Gas Recirculation) or pre-emission control system.  
F - Use carb-to-manifold base gasket supplied with carb.  
I - Carburetor has no provision for evaporative canister.  
K - Carburetor requires #8008 or #8024 stud, nut and washer kit. Determine length needed before installation.  
GASKETS AND SEALANT  
1. Use only original equipment intake gasket set GM #12529196 when installing this Edelbrock manifold. If the original  
gasket is in good condition, it may be re-used.  
2. Do not use any type of gasket sealer on intake gaskets. The rubber O-rings will seal without chemical sealers.  
3. Eliminate the end seals. Use automotive grade RTV silicone instead. Apply a bead of sealant approximately 1/4" high  
across the block end seal surface, overlapping the intake gasket at the four corners. This method eliminates end seal  
slippage and deterioration.  
Page 1 of 2  
Brochure #63-0152  
Rev. 11/02  
©2002 Edelbrock Corporation  
 

Compaq Printer 5525B User Manual
Craftsman Router 32017541 User Manual
Crosley Radio Turntable CR49 User Manual
Dimplex Water Heater WB3 User Manual
Ducane Gas Grill 20208569 User Manual
DXG Technology Camcorder DXG 505V User Manual
Elation Professional Work Light Spot 250 User Manual
Ford Automobile 2008 Expedition User Manual
Freecom Technologies Computer Drive Hard Drive Secure User Manual
Garmin Fish Finder 190 00864 01 User Manual