Chamberlain Work Light 995LM User Manual

Model 995LM SecurityRemote Light Control  
Modèle N° 995LM SecurityTélecommande d’eclairage  
Modelo 995LM SecurityControl Remoto de luz  
Light Control Actuator  
Commutateur de commande d’éclairage  
Actuador de control de luz  
WARNING  
To prevent possible SERIOUS INJURY or DEATH from electrocution  
or fire, the light control is ONLY for indoor use.  
Antenna  
Antenne  
Antena  
AVERTISSEMENT  
Pour éviter les risques de BLESSURE GRAVE ou de MORT causés  
par l’électrocution ou l’incendie, la commande d’éclairage doit être  
utilisée UNIQUEMENT pour l’intérieur.  
Learn Button  
ADVERTENCIA  
Bouton LEARN  
Botón "APRENDER" (Learn)  
Learn Indicator Light  
Voyant indicateur d’apprentissage  
Luz indicadora de aprendizaje  
Para prevenir LESIONES GRAVES O LA MUERTE posibles de  
electrocución o incendio, el control de luz es para uso interior  
SOLAMENTE.  
OWNER’S INSTRUCTIONS  
ENGLISH  
The Remote Light Control is designed to operate lights  
according to the rating chart shown. Please read the  
instructions and power limitations carefully to ensure proper use  
and maximum safety. NOT recommended for use with toasters,  
coffee pots, florescent or halogen lighting systems.  
ERASING CODES  
If the receiver LEARN button is pressed and held until the  
yellow indicator light alongside goes out (in about 6 seconds),  
all memorized codes will be erased.  
This Light Control can be operated by Model 900 Series  
portable remote controls and Keyless Entries.  
OPERATING INSTRUCTIONS  
If two or more light controls are installed, they must be located  
at least 10 feet apart to prevent electronic interference.  
The Remote Light Control receiver needs to learn the  
remote control code. Follow the instructions below:  
• First, plug the lamp into a wall outlet and turn it ON.  
• With the lamp still in the ON position, plug it into polarized  
outlet on the light control. Plug the Light Control into a 120Vac  
polarized outlet. The bulb will not light.  
• Plug the light control into a 120Vac polarized outlet. The plug  
contacts are designed for polarized outlets only.  
• Press and release the “learn” button on the Light Control with  
a pen or pencil tip. The learn indicator  
light will glow steadily for 30 seconds.  
• TO TEST: Press and release the light control actuator. The  
light should turn ON. Press the remote control push button.  
The light should turn OFF.  
• Within 30 seconds, press and hold the  
button on the hand-held remote.  
Select a  
If the remote control does not activate the light, check to be sure:  
You are pressing the remote control push button selected to  
operate the light control.  
• Release the remote control push button.  
Code setting is now complete.  
push button  
• The remote control battery has power. Refer to the remote  
control instructions for battery changing information.  
The remote control push button must be held down until the  
receiver indicator light flashes for the light control to learn the  
remote control's code.  
NOTICE: To comply with FCC and/or Industry Canada (IC) rules, adjustment or  
modifications of this receiver and/or transmitter are prohibited, except for changing the  
code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.  
RATING  
Resistive Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 Amps  
Motor Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1/3 HP  
Incandescent Lamp . . . . . . . . . . . . . . . . . . . . . . . .600 Watts  
 

Blodgett Hot Beverage Maker KLT 20G User Manual
Blue Wave Boats Boat MS 57 User Manual
Bose Headphones in ear headphone User Manual
Campbell Hausfeld Cordless Saw CL154000AV User Manual
Campbell Hausfeld Pressure Washer PW1510 User Manual
Carrier Automobile Parts V2203 DI 26 00128 User Manual
Chamberlain Garage Door Opener 2580C 1 2 HP User Manual
Chauvet Printer B 250 User Manual
Chicago Electric Welding Consumables 66788 User Manual
Chromalox Gas Heater PE433 3 User Manual